Slide Gate Operators

Here you can edit the background of the section

MODEL L-3 SLIDE GATE OPERATOR

The L-3 gate operator has the capacity to operate slide gates up to 1200 lbs. and 40 feet in length at 100% duty cycle under extreme conditions.

More Information

Model L-3 Slide Gate Operator – Residential and commercial Class I, Class II, Class III, and Class IV Vehicular Slide Gate Operator. The L-3 gate operator has the capacity to operate slide gates up to 1200 lbs. and 40 feet in length at 100% duty cycle under extreme conditions. It’s efficient mechanism provides a solution for high traffic commercial slide gate applications.

Design Features Overview:
Some of the standard features include: 7 year residential and 5 year commercial warranty, UL 325 and 991 listing, innovative fine tune adjustment for the end of gate travel (down to 1/8”), back drivable unit featuring direct drive mechanism, soft-start and soft-stop with adaptive learn algorithm, easy accessed switch for manual operation, 120/220 VAC single phase power source, a built in three push button station, a built in battery backup capable of 100 cycles in case of power failure, on-board lightning protection, and easy access to limit switches.

Operational Specifications:
- Operational Voltage … 24 VDC with 1/2 H.P. Motor
- Main Power Source … 120 / 220 VAC Single Phase
- Battery … 7 AmpHr 12 VDC x 2
- Max Gate Capacity … 1200 lbs /12′ or 800 lbs /16′
- Max Operating Speed … 13-16 seconds per 90˚
- Battery Backup … 300 Full Cycles (600 lbs. / 12’ gate)
- Maximum Operational Duty … Continuous Cycle
- Operating Temperature … – 4˚ F to + 158˚ F

MODEL H-10 SLIDE GATE OPERATOR

The H-10 gate operator has the capacity to operate slide gates up to 2000 lbs. and 45 feet in length at 100% duty cycle under extreme conditions.

More Information

Model H-10 Slide Gate Operator – Residential and commercial Class I, Class II, Class III, and Class IV Vehicular Slide Gate Operator. The H-10 gate operator has the capacity to operate slide gates up to 2000 lbs. and 45 feet in length at 100% duty cycle under extreme conditions. It’s efficient mechanism provides a solution for high traffic commercial slide gate applications.

Design Features Overview:
Some of the standard features include: 7 year residential and 5 year commercial warranty, UL 325 and 991 listing, innovative fine tune adjustment for the end of gate travel (down to 1/8”), back drivable unit featuring direct drive mechanism, soft-start and soft-stop with adaptive learn algorithm, easy accessed switch for manual operation, 120/220 VAC single phase power source, a built in three push button station, a built in battery backup capable of 100 cycles in case of power failure, on-board lightning protection, and easy access to limit switches.

Operational Specifications:
- Operational Voltage … 24 VDC with 1 HP Equivalent Motor
- Main Power Source … 120 / 220 VAC Single Phase
- Battery … 7 AmpHr 12 VDC x 2
- Max Gate Capacity … 2000 lbs /45′
- Max Operating Speed … 12” per second
- Battery Backup … 100 Full Cycles (1000 lbs. / 20’ gate)
- Maximum Duty Cycle … 100% Continuous Cycle
- Operating Temperature … – 4˚ F to + 158˚ F

MODEL K-2 SLIDE GATE OPERATOR

The K-2 slide gate operator operates a highly efficient direct motor drive which allows operation at 100% duty cycle.

More Information

Residential Class I, Class III, and Class IV Vehicular Slide Gate Operator. The K-2 slide gate operator operates a highly efficient direct motor drive which allows operation at 100% duty cycle.

Design Features Overview:
Some of the standard features include: 5 year warranty, UL 325 and 991 listing, an innovative fine tune adjustment for the end of gate travel ( down to 1/8” ), back drivable unit to help compliance with fire department authorities, soft-start and soft-stop with adaptive learn algorithm, easy accessed switch for manual operation, 120/220 VAC single phase power source, a built in three push button station, a built in battery backup capable of 100 cycles in case of power failure, on-board lightning protection, and easy access to limit switches.

Operational Specifications:
- Operational Voltage … 24 VDC with 1/2 HP Motor
- Main Power Source … 120 / 220 VAC Single Phase
- Battery … 7 AmpHr 12 VDC x 2
- Max Gate Capacity … 650 lbs / 27′
- Max Operating Speed … 12” per second
- Battery Backup … 100 Full Cycles (650 lbs. / 20’ gate)
- Maximum Duty Cycle … 100% Continuous Cycle
- Operating Temperature … – 4˚ F to + 158˚ F

MODEL Q-4 SLIDE GATE OPERATOR

The Q-4 brings the advantages of DC gate operators to heavy slide gate operation. The advanced motor control circuit driving the motor guarantees long life.

More Information

Commercial Class II, Class III, and Class IV Vehicular Slide Gate Operator. The Q-4 brings the advantages of DC gate operators to heavy slide gate operation. The advanced motor control circuit driving the motor guarantees long life.


Design Features Overview:
Some of the standard features include: 5 year commercial warranty, UL 325 and 991 listing, innovative fine tune adjustment for the end of gate travel ( down to 1/8” ), adaptive algorithm with smooth acceleration and deceleration, more than 1/2 kilowatt of power, built in battery backup capable of 100 cycles in case of power failure, a powerful and efficient gear head motor, fail-safe / fail-secure electromechanical lock, and adjustable height for the main drive.

Operational Specifications:
- Operational Voltage … 24 VDC with 2 HP Motor
- Main Power Source … 120 / 220 VAC Single Phase
- Battery ( Optional )… 33 to 100 AmpHr 12 VDC x 2
- Max Gate Capacity … 4000 lbs / 60′
- Max Operating Speed … Up to 16” per second
- Battery Backup … 100 Full Cycles (2000 lbs. / 40’ gate)
- Maximum Duty Cycle … 100% Continuous Cycle
- Operating Temperature … – 4˚ F to + 158˚ F

SL585 INDUSTRIAL SLIDE GATE OPERATOR

The powerful design supports gate lengths up to 70 feet and gate weights up to 1,600 pounds. 

More Information

The LiftMaster® SL585 is a durable heavy-duty gear-driven operator for use on heavy gates and high-cycle applications such as gated communities and industrial locations. The powerful design supports gate lengths up to 70 feet and gate weights up to 1,600 pounds. A strong powder-coated galvanized steel chassis, all-weather gearbox, as well as a weather-resistant, lockable cover ensure years of rugged and reliable performance. This model is ideal for heavy commercial and industrial installations and is UL325-compliant.

Features:
- Built-in radio receiver
- Universal footprint
- Larger control box
- Integrated 3-button control station
- Large accessory tray
- External manual disconnect
- External reset button
- Inherent obstruction sensing
- External obstruction sensing
- Advanced dual gate operation
- Sequenced access management
- Digital logic control
- LED indicators
- Warning device
- Loop detector inputs
- Timer to close
- Maximum run timer
- Emergency stop button
- Maglock control
- Control inputs
- Mechanical braking
- Limit settings
- Surge & spike protection
- Hinged access cover
- 2-year warranty

SL595 HEAVY-DUTY INDUSTRIAL SLIDE GATE OPERATOR

This is an extreme heavy-duty operator for industrial locations such as manufacturing plants and truck depots. The extremely powerful design supports gate lengths up to 90 feet and gate weights up to 2,500 pounds.

More Information

The LiftMaster® SL595 is an extreme heavy-duty operator for industrial locations such as manufacturing plants and truck depots. The extremely powerful design supports gate lengths up to 90 feet and gate weights up to 2,500 pounds. Fully enclosed NEMA 3R oil-tight, weatherproof lockable cabinet and a high-starting continuous-duty torque motor with built-in overload protection ensure rugged and reliable performance. This model is ideal for the heaviest industrial installations and is UL325-compliant.

Features:
- Built-in 312HM radio receiver
- Larger control box
- Integrated 3-button control station
- External reset button
- Inherent obstruction sensing
- External obstruction sensing
- Advanced dual gate operation
- Sequenced access management
- Digital logic control
- LED indicators
- Warning device
- Loop detector inputs
- Timer to close
- Maximum run timer
- Emergency stop button
- Maglock control
- Control inputs
- Mechanical braking
- Limit settings
- Surge & spike protection
- Manual disconnect
- NEMA 3R enclosure
- Hinged access cover
- 2-year warranty.

 

Liftmaster Model SL575 Slide Gate Operator

This resilient operator offers many standard features such as dual gate operation, sequenced access management, diagnostic LEDs, and more.

More Information

The LiftMaster® SL575 is a reliable continuous-duty operator for use on heavy-gate applications in commercial and light industrial locations. This resilient operator offers many standard features such as dual gate operation, sequenced access management, diagnostic LEDs, and more. The SL575 supports gate lengths up to 50 feet and gate weights up to 1,800 pounds, making it ideal for commercial and light industrial installations.


Standard Features:
- Built-in 312 HM radio receiver
- Universal footprint
- Larger control box
- Integrated 3-button control station
- Large accessory tray
- External manual disconnect
- External reset button
- Self-locking drive
- Inherent obstruction sensing
- External obstruction sensing
- Advanced dual gate operation
- Sequenced access management
- Digital logic control
- LED indicators
- Warning device
- Loop detector inputs
- Timer to close
- Maximum run timer
- Emergency stop button
- Maglock control
- Control inputs
- Mechanical braking
- Limit settings
- Surge & spike protection
- Hinged access cover
- 2-year warranty

Liftmaster Model HS670 Slide Gate Operator

The extremely powerful design supports gate lengths up to 80 feet and gate weights up to 5000 pounds.

More Information

The LiftMaster® HS670 Heavy-Duty Operator is designed for commercial or industrial applications that require high cycles and large gates. The extremely powerful design supports gate lengths up to 80 feet and gate weights up to 5000 pounds. Powder-coated, weatherproof lockable 14-gauge cabinet and a high-starting continuous duty torque motor with built-in overload protection ensures rugged and reliable performance. These models are ideal for the heaviest commercial installations and are UL325 compliant.


Standard Features:
- Built-in radio receiver
- Inherent obstruction sensing
- External obstruction sensing
- Maglock control
- Warning device
- Loop detector inputs
- Manual hydraulic release
- Control inputs
- Advanced dual gate operation
- Timer to close
- Sequenced access management (SAM) system
- Digital logic control
- Surge & spike protection
- LED indicators
- Maximum run timer
- Accessory power
- Limit settings
- Emergency stop button
- 2-year warranty

MODEL 746 ER SLIDE GATE OPERATOR

Gear motor for sliding gates with max. weight of 600 kg

More Information

Gear motor for sliding gates with max. weight of 600 kg

- 746 ER Z16 for rack applications.
- 746 ER Z20 for rack applications (400 Kg).
- 746 ER CAT for chain applications
- 746 ER RF for chain applications with idle transmission

Use: residential/condominium

- Maximum anti-crushing safety by coupling the twin-disk oil-bath clutch with the electronic device and encoder
- As the gear motor is non reversing, no electric locks need be installed
- Key protected lever release device
- Magnetic travel limit device, simplified installation of travel limit magnets
- Designed for height and side adjustable fastening
- Control board, protected by a housing, for simplified programming via display.

844 ER SLIDE GATE OPERATOR

Gear motor for sliding gates with max. weight of 1,800 kg

More Information

Gear motor for sliding gates with max. weight of 1,800 kg

- 844 ER Z16 for rack applications
- 844 R for rack applications (without pinion)
- 844 R CAT for chain applications
- 844 R RF for chain applications with idle transmission

Use: condominium/industrial

- Ideal for commercial and industrial applications
- Anti-crushing safety
- As the gearmotor is non reversing, no electric locks need be installed
- In the event of power failure, the key-operated release device makes it possible to open and close the gate manually
- Twin-disk clutch in oil-bath
- Inductive or magnetic travel limit (according to model)

DoorKing Commercial & Industrial Slide Gate Operator Model 9000

The DKS 9000 series of slide gate operators offer convenience, reliability and safe operation in a small, compact design.

More Information

The DKS 9000 series of slide gate operators offer convenience, reliability and safe operation in a small, compact design. These operators are ideally used in residential, commercial or industrial high-use applications. The steel frame and belt drive/gear-box reduction system provide a powerful, yet extremely quiet, slide gate operation. The 9000 uses an advanced microprocessor control circuit with outstanding features. Designed with versatility in mind, these operators will fit most slide gate operation requirements.


Features:
- Steel frame provides strength and quiet operation
- “T-Handle” release is easily accessible from front of operator
- Operator re-connects automatically when handle is released
- Adjustable partial open limit
- Direct driven limit nuts for precise gate control
- Auto-close timer 1-30 seconds
- Ports for plug-in open and reverse loop detectors – DKS detectors only
- Selectable loop/reverse input function; stop or reverse
- Anti-tailgating feature helps to control un-authorized traffic
- Standard normally closed stop circuit
- Gate Tracker reporting output provides operator data to DKS access control system
- Convenience outlets for accessory transformers
- Built-in power switch and alarm reset switch
- Simple bi-parting gate interface

Specifications:
- Maximum gate width 35-ft.
- Maximum gate weight 1000 pounds* (1/2 HP) or 1500 pounds* (1 HP). (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.)
- 1/2 or 1 HP continuous-duty motor
- 115, 230*, 208*, 460* VAC. (*230, 208, and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.)
- Class I, II, III and IV applications
- Compliant with UL 325 and 991, ETL Listed. (Note: To be compliant with UL 325 and industry safety guidelines, additional secondary entrapment prevention devices are required to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)
- Dimensions: 18.375″W x 31.675″H x 23.25″D

DoorKing Commercial & Industrial Slide Gate Operator Model 9150

These operators are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications.

More Information

Model 9150 operators are designed to operate vehicular slide gates in residential, commercial and industrial applications. These operators are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operators can be pad or post mounted to meet any installation requirements. The 9150 can be equipped with a factory installed DC Convenience Open option which will automatically open the gate in the event of a power outage.
Features
- Self-adjusting, no maintenance magnetic limits.
- Partial-open feature.
- Anti-tailgating feature.
- Gate tracker reporting output.
- Ports for plug-in loop detectors.
- DC Powered Convenience Open (Optional).
- Two convenience outlets.
- Fail-safe release (fail-secure optional).
- Programming switches.
- Built-in reset switch.
- Built-in power On/Off switch.


Specifications Model 9150 With 1/2 HP Motor
- Maximum gate length 30-feet.
- Maximum gate weight 1000 pounds*. (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator. If DC Convenience Open option is installed, maximum gate weight is 1300 pounds. Other external factors may affect the performance of the gate operator.)
- 1/2 HP continuous-duty motor.
- 115, 208*, 230*, 460* VAC (*208, 230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.)
- Operator is shipped with chain brackets and 20-feet of #40 chain.
- Class I, II, III and IV applications.
- Compliant with UL 325 and 991. ETL listed. (Note: To be compliant with UL 325 and industry safety guidelines, a secondary entrapment prevention device(s) is required to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)
- Dimensions: 15.25″W x 24.75″H x 16.75″D

Specifications Model 9150 With 1 HP Motor
- Maximum gate length 45-feet.
- Maximum gate weight 1500 pounds*. (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator. If DC Convenience Open option is installed, maximum gate weight is 1300 pounds. Other external factors may affect the performance of the gate operator.)
- 1 HP continuous-duty motor.
- 115, 208*, 230*, 460* VAC (*208, 230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.)
- Operator is shipped with chain brackets and 20-feet of #40 chain.
- Class I, II, III and IV applications.
- Compliant with UL 325 and 991. ETL listed. (Note: To be compliant with UL 325 and industry safety guidelines, a secondary entrapment prevention device(s) is required to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)
- Dimensions: 15″W x 24″H x 16.5″D

DoorKing Residential Slide Gate Operator Model 9050

The Model 9050 operator is designed to operate vehicular slide gates in residential applications only. 

More Information

The Model 9050 operator is designed to operate vehicular slide gates in residential applications only. The operator is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operator can be pad or post mounted to meet any installation requirements.

Features
- Self-adjusting, no maintenance magnetic limits.
- Ports for plug-in loop detectors.
- Two convenience outlets.
- Fail-safe release (fail-secure optional).
- Programming switches.
- Built-in reset switch.
- Built-in power On/Off switch.

Specifications
- Maximum gate length 16-feet.
- Maximum gate weight 500 pounds*. (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.)
- 1/2 HP limited-duty motor.
- 115 VAC, 4.3 Amps.
- Class I applications.
- Compliant with UL 325 and 991. ETL Listed. (Note: To be compliant with UL 325 and industry safety guidelines, a secondary entrapment prevention device(s) is required to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)
- 12″W x 24″H x 11.5″D

Here you can edit the background of the section

DoorKing Industrial Slide Gate Operator Model 9200

These operators should never be used in applications serving the general public.

More Information

DoorKing’s Maximum Security operators are designed to operate vehicular slide gates in limited (Class III) and restricted (Class IV) applications only. These operators should never be used in applications serving the general public. These operators are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. Center mounting the operator requires the pedestal mounting base (optional on 9210, 9220). The speed control on these operators (except 9210) allows the user to set the speed of the gate from 1/2 to 2 feet/sec., and provides slow-start and slow-stop functions as well.

Features:
- Direct driven limit nuts.
- Anti-tailgating feature.
- Adjustable mid-stop.
- Gate tracker reporting output.
- Ports for plug-in loop detectors.
- Two convenience outlets.
- Fail-secure operation includes crank for manual operation.
- Programming switches.
- Built-in reset switch.
- Built-in power On/Off switch.

DoorKing Maximum Security Slide Gate Operator Model 9500

The 9500 series uses a high tensile steel alloy roller chain as the pulling medium, which is immune to slippage on un-even terrain and simplifies installation.

More Information

The DKS 9500 series operators are designed to operate very heavy vehicular slide gates in limited (Class III) and restricted (Class IV) applications only. These operators should never be used in applications serving the general public. The 9500 series uses a high tensile steel alloy roller chain as the pulling medium, which is immune to slippage and un-even terrain and simplifies installation. These operators include a speed control module which allows the user to set the speed of the gate and have a slow-start and slow-stop function as well.

Features:
- Speed control module.
- Slow start / slow stop.
- Direct driven limit nuts.
- Anti-tailgating feature.
- Adjustable partial open..
- Gate tracker reporting output.
- Built-in diagnostics.
- Ports for plug-in loop detectors.
- Selectable stop / reverse loop functions.
- Two 115 VAC convenience outlets.
- Fail-secure operation includes crank for manual operation.
- Programming switches.
- Built-in 3-button control (open-close-stop)
- Built-in power On/Off switch.

Specifications:
- Maximum gate length 160-feet.
- HP, maximum gate weight*, speed and chain size:
- 9530 – 3 HP, 10,000 Lbs., 2 ft/sec, #80 chain.
- 9550 – 5 HP, 20,000 Lbs., 1 ft/sec, #100 chain.
- 9555 – 5 HP, 10,000 Lbs., 4 ft/sec, #80 chain.
- 9575 – 7.5 HP, 25,000 Lbs., 2 ft/sec, #100 chain.
- (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.)
- 10:1 or 40:1 gear reduction running in a continuous oil bath (dependant on model).
- Electronic braking – all models.
- Self adjusting disc brake with manual release (9555 only).
- 208, 230, 460 VAC three-phase.
- Operator is shipped with chain brackets and 20-feet of #80 or #100 chain (dependant on model).
- Class III and IV applications only.
- ETL Listed. (Note: To be compliant with UL 325 and industry safety guidelines, external entrapment prevention devices are required to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)
- Dimensions: 54 “W x 59 “H x 26 “D

DoorKing Commercial Slide Gate Operator Model 9100

The 9100 is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications.

More Information

The Model 9100 operator is designed to operate vehicular slide gates in residential and commercial applications. The 9100 is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operator can be pad or post mounted to meet any installation requirements.

Features:
- Self-adjusting, no maintenance magnetic limits.
- Partial-open feature.
- Anti-tailgating feature.
- Gate tracker reporting output.
- Ports for plug-in loop detectors.
- Two convenience outlets.
- Fail-safe release (fail-secure optional).
- Programming switches.
- Built-in reset switch.
- Built-in power On/Off switch.

Specifications:
- Maximum gate length 30-feet.
- Maximum gate weight 1000 pounds*. (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.)
- 1/2 HP continuous-duty motor.
- 115 VAC, 5.4 Amps.
- Operator is shipped with chain brackets and 20-feet of #40 chain.
- Class I, II, III and IV applications.
- Compliant with UL 325 and 991. ETL Listed. (Note: To be compliant with UL 325 and industry safety guidelines, a secondary entrapment prevention device(s) is required to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)
- Dimensions: 12″W x 24″H x 11.5″D

HYSECURITY SLIDESMART CNX15

The 9100 is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. SlideSmart CNX is the most capable of its kind and the first to offer a robust smartphone app to simplify installation..

More Information

SlideSmart CNX is the most capable of its kind and the first to offer a robust smartphone app to simplify installation.

Advanced: Brushless DC motor technology, solid state limit sensors, and direct drive power train for superior control

UPS: Standard battery backup to keep gates moving up to 100 cycles, with battery upgrades for up to 450 cycles

Programmable: Over 70 user configurable settings to meet site specific requirements

Connected: Bluetooth wireless connectivity for setup. HyNet technology for remote monitoring, management, and maintenance

HYSECURITY SILDERDRIVER

Providing durable security for over three decades, SlideDriver is the preferred solution for sensitive perimeters.

More Information

Providing durable security for over three decades, SlideDriver is the preferred solution for sensitive perimeters.

Powerful: Move gates up to 20,000 lbs

Durable: Decades long life and low maintenance

Tough: Secure steel chassis and tamper resistant cover

Smart: Integrated primary/secondary controls and preprogrammed relay setting